Page 7 of catalogue Triple trough gutter tile of Dachziegelwerke Nelskamp GmbH

Additional fastening principle for left verge
1 2 3 1 Included with every left verge tile: clip, SX 5 plug and Phillips screw VA 3.5 x 25 mm (ready assembled); wood screw VA 4.5 x 45 mm to fasten the verge. 2 As usual, fasten the verge tile with the VA 4.5 x 45 mm screw at least 24 mm into the lath. 3 The pre-assembled new fastening (clip, plug, Phillips screw) should be fastened to the head of the verge. 4 Fasten fingertight. 5 The verge tiles have a special slit 8 on their underside. When laying the overlapping verge tiles press firmly into place until the Clips are heard to catch in this slit. 9 During further installation of the verge tile proceed as described above.

4

5

6

7

8

9

Shed roof tile
Shed Roof tiles should be fastened to the furring (see detail verge). Size sheets can be downloaded from the Internet or on the data service CD
tch f pi roo on ing mm end 455 dep 0 to 12 from

Aeration and ventilation in steep roof
1 Eaves fresh air element 2 Copper roll/Alu roll 2000 3 Clay dormer ventilator with fitted screen vent cross-section ~ 20 cm2 3 1
90° 60° 70° 80° Counter-laths Underlay/undercover sheet Eaves fresh air element

2

Aeration/venting

of mm th wid 340 o m fro ide t s rge ve

1) The vent cross-section at the eaves should be at least 200 cm2/m of eaves. 2) The vent cross-section at the ridge or crest should be at least 0.5‰ of the total corresponding roof area, though at least 50 cm2. (according to DIN 4108-3)

90° 80°= RP 10° 70°= RP 20° 60°= RP 30°

• lath size of ~ 120 - 455 mm • lath size of ~ 120 - 445 mm • lath size of ~ 120 - 415 mm • lath size of ~ 120 - 395 mm

Installation instructions for alu base tile with single step/walking grid tile
Of stainless steel/aluminium. No supporting laths needed! Fastening to supporting lath: Aluminium tile fastened to lath with 2 Screws (V2A screw included)
Processing acc. to DIN 18160-5 Article ≤ 45° > 45° Walking grid every every tile row of tiles row of tiles Alu base tile every every w step tile row of tiles row of tiles

Clear spacing of laths
If using large area clay roof tiles a clear lath spacing of ≤ 0.4 m (rounded off up to and including 44.4 cm) is allowed. This is confirmed by the „Trade Association Technical Committee on Building“. • See Technical Rules of the German Roofing Trade, notes on wood and timber materials - According to the BG Rules "Roofing work” (BGR 203) or "Carpentry and wood work” (BGR 214), roof areas with that have roof lath intervals with a clear span of ≤ 0.4 m are regarded as closed roof areas .
cm .4 50 th ng le

ing ver * co cm x. .4 Ma 44 x. ma to .0 40

cm 6.0

Roof lath 2 x fastening in the counter-lath

tested to DIN EN 516

th m g la 0 m rtin x 6 ppo 40 0 su S1

The same applies for alu pantiles with snow rib or round wood holder, whereby the max. support spacing should not exceed 90 cm. For higher demands you should reduce the support spacing.

* The approved 0.4 m may not be rounded off to ≤ 44.4 cm clear spacing of roof laths.

On the NELSKAMP data service CD or as a download on the Internet from www.nelskamp.de • Product specifications • Laying instructions • CAD data

Subject to technical changes. The dimensions are planning figures and should be checked before laying.