Page 5 of catalogue Triple trough gutter tile of Dachziegelwerke Nelskamp GmbH

Laying the NIBRA® tile MS 5.
Type of laying: Simple roof cladding or pattern roof cladding Technical data
Roof tile Manufacturer Overall length Overall width Covering length Mean covering width Requirement per m2 Weight per tile Weight per m2 Regular roof pitch Laths Recommended storm clip Laths Recommended storm clip * Possible covering length with fully NIBRA tile MS 5 Nelskamp (D) ~ 59.2 cm ~ 37.4 cm ~ 44.0 - 50.4* cm ~ 32.9 cm ~ 6.0 pieces ~ 6.8 kg ~ 40.8 kg 22° 30 x 50 mm 409/009 40 x 60 mm 409/009 covered roofs 44.0 - 54.0 cm
®

Material requirements for coverage
Laths Counter-laths Roof tile Packing unit* Tiles per pallet Tiles per stack 1/3 tile Verge tile Ridge or crest tile Copper roll/Alu roll 2000 (5 m per roll) Ridge/crest clip 470/41 Wood Screws Ridge or crest initial tile Ridge end tile Ridge lath holder Crest lath holder Eaves fresh air element
* only applies for deliveries in Germany

~ 2.2 m/m2 (incl. 10% waste) ~ 1.7 m/m2 (incl. 10% waste) ~ 6.0 pieces/m2 120 pieces 20 pieces individual ~ 2.0 pieces/m ~ 2.6 pieces/m as required 1.0 piece per ridge tile 1.0 piece per ridge tile d = 4.5 mm Screw depth: 24 mm 1.0 piece per ridge or crest start 1.0 piece per ridge end 1.0 piece per rafter 1.0 piece/ ~ 70 cm ~ 1.1 piece/m Fresh air ~ 200 cm2/m

Laying!
The following applies when laying our clay Roof tiles: 1. The NELSKAMP manufacturer's instructions take priority (laying instructions) 2. The specialist rules of the roofing trade (rules for coverings with clay roof tiles) 3. The German Construction Contract Procedures (VOB) (clay roof tile cover)

Way of walking
Way of walking during laying. The optimum load point is directly beneath the height overlap.

Covering widths
20 110 329 110 68 20

45 70

45

45

45

1/3 tile
20 65 329 110 113 20

70

covering width left verge tile = 11.0 cm

Chalk line marking lining out every 3 - 5 rows

covering width right verge tile = 6.8 cm

Regular roof pitch for clay roof tiles

22° 10°

Regular roof pitch tile MS 5

If the pitch is below the regular roof pitch the additional measures of the roofing trade rules must be carried out (cf. table). With equivalent roof substructure alternatives: pay attention to the manufacturer's and laying instructions. Warranty must be assumed by the relevant manufacturer.

Minimum roof pitch for roofing with clay roof tiles

Classification of additional measures for the NIBRA® tile MS 5 according to the basic rules of the German Roofing Trade, 22° regular roof pitch, minimum roof pitch 10°
Use of the attic. in particular for living Roof pitch in degrees (rafter pitch) no further increased requirement ≥ 22° ≥ 16° ≥ 12° ≥ 10° underlayment rainproof roof substructure rainproof roof substructure Higher requirements Design *with special roof shapes *with long rafters *with very jointed roof areas (e.g. through dormers. valleys. etc.) one further increased requirement underlayment underlayment rainproof roof substructure waterproof roof substructure Climatic conditions *exposed location *extreme locations *snowy areas *windy areas *special meteorological conditions two further increased three further increased requirements requirements overlapping or interlocked underlayment undercover overlapping or interlocked welded or bonded undercover undercover waterproof roof substructure waterproof roof substructure

rainproof roof substructure waterproof roof substructure

* The additional measures named in the table are minimum measures. With very high requirements and/or special local conditions a higher-value additional measure should be chosen (Leaflet for roof substructures, Table 1, German Roofing Trade Rules). Higher-value additional measures can always be used in place of the minimum measures.