Page 5 of catalogue Flat tile of Dachziegelwerke Nelskamp GmbH

Laying the NIBRA® flat tile G 10.
Type of laying: Simple roof cladding or pattern roof cladding The optical covering pattern should be agreed with the parties involved in the building before laying. Technical data
Roof tile Manufacturer Overall length Overall width Mean covering length Mean covering width Requirement per m2 Weight per tile Weight per m2 Regular roof pitch Laths Recommended storm clip Laths Recommended storm clip NIBRA® flat tile G 10 Nelskamp (D) ~ 48.2 cm ~ 29.3 cm ~ 39.1 cm ± 10 mm ~ 24.8 cm ~ 10.0 pieces ~ 4.4 kg ~ 44.0 kg 25° 30 x 50 mm 435/103 40 x 60 mm 435/104

Material requirements for coverage
Laths Counter-laths Roof tile Packing unit* Tiles per pallet Tiles per stack Half tile Double flap Verge tile Ridge or crest tile Copper roll/Alu roll 2000 (5 m per roll) Ridge/crest clip 470/41 Ridge/crest clip 470/166 Wood Screws Ridge or crest initial tile Ridge end tile Ridge lath holder Crest lath holder Eaves fresh air element
* only applies for deliveries in Germany

~ 2.5 m/m2 (incl. 10% waste) ~ 1.7 m/m2 (incl. 10% waste) ~ 10.0 pieces/m2 240 pieces 30 pieces individual ~ 2.5 pieces/m for left side of roof only ~ 2.5 pieces/m ~ 2.6 pieces/m as required 1.0 piece per ridge tile standard 1.0 piece per ridge tile square 1.0 piece per ridge tile d = 4.5 mm Screw depth: 24 mm 1.0 piece per ridge or crest start 1.0 piece per ridge end 1.0 piece per rafter 1.0 piece/ ~ 70 cm ~ 1.1 piece/m Fresh air ~ 200 cm2/m

Laying!
The following applies when laying our clay Roof tiles: 1. The NELSKAMP manufacturer's instructions take priority (laying instructions) 2. The specialist rules of the roofing trade (rules for coverings with clay roof tiles) 3. The German Construction Contract Procedures (VOB) (clay roof tile cover)

Covering widths
18 210 248 125 248 165 18

45 65

45

45

45

45

65

18

165

248

125 Chalk line marking Lining out every 3 - 5 rows

248

210

18

covering width left verge tile = 21.0 cm covering width double flap tile = 24.5 cm

covering width right verge tile = 16.5 cm

Regular roof pitch for clay roof tiles

25°

Regular roof pitch flat tile G 10

If the pitch is below the regular roof pitch the additional measures of the roofing trade rules must be carried out (cf. table). With equivalent roof substructure alternatives: pay attention to the manufacturer's and laying instructions. Warranty must be assumed by the relevant manufacturer.

10°

Minimum roof pitch for roofing with clay roof tiles

Classification of additional measures for the NIBRA® flat tile G 10 according to the basic rules of the German Roofing Trade, 25° regular roof pitch, minimum roof pitch 10°
Use of the attic. in particular for living Roof pitch in degrees (rafter pitch) no further increased requirement ≥ 25° ≥ 19° ≥ 15° ≥ 10° underlayment rainproof roof substructure rainproof roof substructure Higher requirements Design *with special roof shapes *with long rafters *with very jointed roof areas (e.g. through dormers. valleys. etc.) one further increased requirement underlayment underlayment rainproof roof substructure waterproof roof substructure Climatic conditions *exposed location *extreme locations *snowy areas *windy areas *special meteorological conditions three further increased two further increased requirements requirements overlapping or interlocked underlayment undercover overlapping or interlocked welded or bonded undercover undercover waterproof roof substructure waterproof roof substructure

rainproof roof substructure waterproof roof substructure

* The additional measures named in the table are minimum measures. With very high requirements and/or special local conditions a higher-value additional measure should be chosen (Leaflet for roof substructures, Table 1, German Roofing Trade Rules). Higher-value additional measures can always be used in place of the minimum measures.