Page 7 of catalogue Flat roof tile of Dachziegelwerke Nelskamp GmbH

Details eaves design
The dimensions are planning figures and should be checked before laying depending on the design and local circumstances.

1 With gutter & vent element
r fte f ra do en

2 High-level gutter (recommended for flat roof pitches < 22°)
Tile overhang in gutter max. 1/3 of gutter width
d of o en cm t ~ 32 h s lat Eave r rafte

h~ lat ves Ea

cm 40

to

Vent element

Eaves plate Fresh air Drip plate

Aeration and ventilation in steep roof
1 Eaves fresh air element 2 Copper roll/Alu roll 2000 3 Clay dormer ventilator with fitted screen vent cross-section ~ 15 cm2 3 1
Counter-laths Underlay/undercover sheet Eaves fresh air element

Shed roof tile
Shed Roof tiles should be fastened to the furring (see detail verge). (1) The length should normally be determined in the water rabbet.
mm 80 to 2 50 1 mm 225 5 to 7
(1)

2

m 80 o1 0t 10 m

Size sheets can be downloaded from the Internet or on the data service CD 60° 70° 80°

90°

Aeration/venting

1) The vent cross-section at the eaves should be at least 200 cm2/m of eaves. 2) The vent cross-section at the ridge or crest should be at least 0.5‰ of the total corresponding roof area, though at least 50 cm2. (according to DIN 4108-3)

90°

Installation instructions for safety step tile/ walking grid tile
Every safety step tile/walking grid tile must be provided with an additional supporting-safety lath (same lath cross-section as supporting laths). Fastening to supporting lath: two corrosion-proof wood Screws (4.5 x 45 mm per tile)
Processing acc. to DIN 18160-5 Article ≤ 45° > 45° Walking grid every 2nd every tile row of tiles row of tiles Safety every every step tile row of tiles row of tiles Roof lath 2 x fastening in the counter-lath Supporting-safety lath

80°= RP 10°

70°= RP 20°

60°= RP 30°

• longest size 275 mm results in a mean lath size 225 mm • shortest size 150 mm results in a mean lath size 100 mm • longest size 280 mm results in a mean lath size 220 mm • shortest size 150 mm results in a mean lath size 90 mm • longest size 270 mm results in a mean lath size 200 mm • shortest size 150 mm results in a mean lath size 80 mm • longest size 260 mm results in a mean lath size 185 mm • shortest size 150 mm results in a mean lath size 75 mm

Storm Clips
No. 435/001 30 x 50 V2A No. 435/002 40 x 60 V2A

tested to DIN EN 516

The same applies for interlocking tiles with snow rib or round wood holder, whereby the max. support spacing should not exceed 90 cm. For higher demands you should reduce the support spacing. No. 409/002 75 x 48 V2A

Installation instructions for universal alu step
A chase is made in the head and foot interlocking joint of the gutter tile using a right angle Grinder with diamond wheel to lead through the stainless steel suspension hinge. Hang the alu mounting bracket in the throat of the gutter tile so that the two rubber profiles with the lower end of the mounting bracket lie on the roof lath. The rubber profiles must rest where the gutter tiles overlap.
Installation instructions on delivery and can be downloaded from the Internet or on the data service CD Step Mounting bracket

According to professional standards, we can supply storm clips for a simple and effective protection against wind suction. They can alternatively be clipped to the laths or knocked into the laths. Resistant to corrosion through stainless steel wire 1.4301 (A2) or ZIAL® coating (corrosion protection).

On the NELSKAMP data service CD or as a download on the Internet from www.nelskamp.de
Stainless steel suspension hinge can be adjusted for roof pitches from 0° - 60° tested to DIN EN 516

• Product specifications • Laying instructions • CAD data

Subject to technical changes. The dimensions are planning figures and should be checked before laying.